|
|
 |
||||||||||||
 |
|||||||||||||
|
|
|||||||||||||
|
|
|||||||||||||
 |
|||||||||||||
TREASURE ACE 100
CONTROL FUNCTIONS
Power/Trash Elimination Control: Rotate knob clockwise to turn detector on. With the detector on and the pointer in the red area just above "ON", the detector is operating in the all metal mode where all metallic targets will be located. Further rotation allows full range adjustment permitting you to determine the junk items you wish to eliminate from detection.
Headphone Jack: Located on the right side of the control panel. Headphones permit the operator to hear small and deep targets that might be missed when using audio from the speaker only.
Audio: The audio level of the Treasure Ace 100 is factory set to be just into the silent range. Targets will not be missed at this level and there will be no loss of target signals.
BATTERY TEST
When the power is turned on, the battery circuit is checked automatically and audibly. Three or more tones and the batteries are very good. Two tones indicate adequate power available. When only one tone or no tone is heard, replace the batteries. The (2) 9-volt batteries are located on the backside of the detector housing behind a sliding door. To replace the batteries, slide the door slightly to the left approximately ½ inch. The door may then be removed to allow access to the batteries. Remove the old batteries and replace with high quality carbon, alkaline, or rechargeable batteries. Make certain the new batteries are installed properly, observing polarity. Replace the battery door and slide it closed. Always make certain that all parts fit snugly, but do not force. OPERATING INSTRUCTIONS:
Set the control knob to the INITIAL SETTING (?) position. The detector is now operating in the TRASH ELIMINATION MODE. To operate the TRASH ELIMINATION MODE and eliminate "junk" targets, adjust the Elimination Control to the desired level for foil, nails, bottlecaps, or pulltabs to be eliminated.
Scan the searchcoil at about one to two feet per second. Maintain a one or two-inch searchcoil height above and level to the ground. All accepted metal targets produce an audio sound when the targets are below the coil. Dig all targets that produce an audio signal.
TARGET ACCEPTANCE & REJECTION
When a metallic object is accepted, the detector's speaker or earphone sound will increase from the factory-set audio threshold level. When a metal object is eliminated (rejected), no sound will be heard. Some rejected targets however, may cause the audio to "break up" or sound erratic. The following explains the various Trash Elimination Settings as shown by the icons placed around the control knob.
In the TRASH Range most small rusty iron will be eliminated just above the All-Metal setting. Salt water is eliminated just below the bottlecap icon.
At the Bottlecap icon, foil, nails and larger rusty iron, will be eliminated.
At the Pulltab icon, pulltabs, bottlecaps, foil, nails and rusty iron will be eliminated.
Nickels, rings, and many foreign coins and tokens may also be eliminated at this setting.
Test typical trash items before operating.
Recovery/Pinpointing:
Recovering a target is accomplished first by Pinpointing.
Pinpoint targets by drawing an imaginary "X" on the ground with the searchcoil at the place where the maximum sound occurs. You will notice that the searchcoil cannot be held motionless above the target, the searchcoil must be moving slightly to detect the targets location.
The next step in recovery usually involves digging. Always make as small a hole as possible. It is quicker, requires less digging, and is easier to fill. And, you should always fill your holes.
MAINTENANCE
v Always remember that your metal detector is a sensitive electronic instrument. It is built to withstand rugged treatment in the outdoors. Use your Garrett detector to the fullest extent possible, and never feel that you have to baby it. Yet, always protect the detector and handle it with reasonable care.
v Try to avoid temperature extremes as much as possible, such as storing the detector in an automobile trunk during hot summer months or outdoors in sub-freezing weather.
v Keep you detector clean. Always wipe the housing after use, and wash the coil when necessary. Protect your instrument from dust and sand as much as possible.
v Your searchcoil is submersible. The control housing is not! Never submerge the control housing and always protect it from heavy mist, rain or blowing surf.
v Disassemble the stem and wipe it clean after use in sandy areas.
v When storing longer than about one month, remove batteries from the detector.
REPAIR SERVICE
v In case of difficulty, read this Owner's Manual again thoroughly to make certain your detector is not inoperable needlessly. Your dealer may also be able to offer advice.
v When your detector must be returned to the factory for service, always include a letter that describes its problem as fully as possible. Before you return your detector to the Garrett factory, make certain:
v You have checked batteries, switches and connectors. (Check batteries especially closely. They are the most common cause of detector "failure".)
v You have checked with your dealer, particularly if you are not familiar with this type of detector.
v You have included a note with the detector describing the problems you are encountering with this detector and conditions under which they occur. Make certain to include your name, address and a phone number where you can be contacted between 8:30 a.m. and 4 p.m., Central Time.
v You have carefully packed the detector in its original shipping carton or other suitable box. Make certain that proper insulation or packing material is used to keep all parts secure. Do not ship stems or headphones unless they are part of the problem. Be certain to return all coils.
v Ship to Garrett Metal Detectors, 1881 W. State St., Garland, TX 75042.
v You can call the Garrett Customer Service Department (800-527-4011) if you have further questions.
v Please allow approximately one week for Garrett technicians to examine and repair your detector after they receive it, plus another week for return shipping to you. All equipment will be returned UPS or parcel post unless written authorization is given by you to ship collect by air parcel post, UPS Blue (air) or air freight.
MIND YOUR MANNERS
Filling holes and obeying no trespassing signs are but two requirements of a dedicated metal detector hobbyist. A sincere request that Charles Garrett makes to every user of one of his detectors is that each place searched be left in a better condition than it was found. Thousands of individuals and organizations have adopted this formal Metal Detector Operators Code of Ethics:
v I will respect private and public property, all historical and archaeological sites and will do no metal detecting on these lands without proper permission.
v I will keep informed on and obey all laws, regulations and rules governing federal, state and local public lands.
v I will aid law enforcement officials whenever possible.
v I will cause no willful damage to property of any kind, including fence, signs and buildings and will always fill holes I dig.
v I will not destroy property, buildings or the remains of ghost towns and other deserted structures.
v I will not leave litter or uncovered items lying around. I will carry all trash and dug targets with me when I leave each search area.
v I will observe the Golden Rule, using good outdoor manners and conducting myself at all times in a manner which will add to the stature and public image of all people engaged in the field of metal detection.
WARNING!
Any metal detector may discover underground power lines, explosives or other items which when struck could cause personal injury. When searching for treasure with your detector, observe these precautions:
v Do not hunt in an area where you believe there may be shallowly buried underground electric lines or pipes.
v Do not hunt in a military zone where bombs or other explosives may be buried.
v Avoid striking any line known to be or suspected to be carrying electrical power.
v Do not disturb any pipeline, particularly if it could be carrying flammable gas or liquid.
v Use reasonable caution in digging toward any target, particularly in areas where you are uncertain of underground conditions.
PATENT PROTECTION: Proof of Garrett excellence is the recognition given them by the following United States patents: 4,709,213; 4,488,115; 4,700,139; 4,398,104; 4,423,377; 4,303,879; 4,334,191; 3,662,255; 4,162,969; 4,334,192; 5,148,151; 5,138,262; 5,721,489; 5,786,696; 5,969,528; Design 274,704 and 297,221; Design 333,990; G.B. Design 2,011,852; Australia Design 111,674 and other patents pending